Graphtec CE6000 Series Service Manual and Parts Catalog


Accurate and concise text, combined with detailed illustrations, lists of error code, instruction and diagrams, guide you through procedure of repair, remediate, maintenance and adjustments your copier, printer or scanner.
Present service manual and parts catalog Graphtec CE6000 Series contain clear instructions and procedures on how to fix the problems occurring in your equipment.
Format of the manual: PDF, makes it easy to navigate, instant download and print. English language.
Table of contents:

1. INTRODUCTION
1.1 Main Specifications
1.2 External Dimensions
1.3 Options
1.4 Supplies

2. PARTS NAMES and FUNCTIONS
2.1 Parts Names and Functions (CE6000-40/60/120/120AMO)
2.2 Assembling the Stand (CE6000-40/60/120/120AMO)
2.3 Parts Names and Functions (CE6000-120AP)
2.4 Assembling the Stand (CE6000-120AP)

3. OPERATIONS
3.1 Control Panel
3.2 Menu Tree

4. RECOMMENDED PARTS LIST
5 LIST OF TOOLS
5.1 Tools
5.2 Greasing And Gluing Points

6. DISASSEMBLY AND REASSEMBLY
6.1 Exterior Parts
6.1.1 Right Side Cover
6.1.2 Left Side Cover
6.1.3 Center Cover
6.1.4 Front Guide (CE6000-40/60)
6.1.5 Front Guide (CE6000-120)
6.1.6 Rear Guide (CE6000-40/60)
6.1.7 Rear Guide (CE6000-120)
6.2 Mechanical Parts
6.2.1 Front Media Sensor
6.2.2 Rear Media Sensor
6.2.3 Push Roller
6.2.4 Push Roller Arm
6.2.5 Cam Sensor Board
6.2.6 Pen Block
6.2.7 Push Roller Sensor
6.2.8 Y-relay Board
6.2.9 Control Panel Key Board
6.2.10 LCD
6.2.11 Y-belt
6.2.12 Y-motor
6.2.13 Main Board
6.2.14 X-motor for the CE6000-40/60
6.2.15 X-motor for the CE6000-120
6.2.16 Y-flexible Cable
6.2.17 Vacuum Fan for the CE6000-40/60
6.2.18 Vacuum Fan for the CE6000-120
6.2.19 Power Supply
6.2.20 Drive Roller shaft
6.2.21 Cutting Mat
6.2.22 Cutting Mat Base Assembly
6.2.23 How to Confirm the Y rail mounting position
6.2.24 Regarding the Push Roller position limit Screws

7. ELECTRICAL ADJUSTMENTS
7.1 DIP Switch Settings
7.2 List of Items Requiring Readjustment
7.3 Explanation of the Values of the Main Board Settings
7.4 Clearing the Non-Volatile RAM
7.5 Selecting Display Language & Length Unit
7.6 The Suffix setting
7.7 Adjusting the Pen Force
7.8 Adjusting the Distance Accuracy
7.9 Adjusting the Registration Mark Sensor Sensitivity
7.10 Adjusting the Offset of the Registration Mark Sensor
7.11 Adjusting the RMS sensor and the Paper sensor position
7.12 Adjusting the Tool Exchange Position (CE6000-120AP)
7.13 Adjusting the Offset between Tool 1 and Tool 2 (CE6000-120AP)
7.14 Adjusting the Y Limit Position (CE6000-120AP)
7.15 Upgrading the System Firmware

8. SERVICE MODES
8.1 Sensor and Key switch test Mode
8.2 Clear Setup Mode
8.3 Printing the Setting of the Plotter
8.4 Test Pattern
8.5 Confirm the Cutting Data
8.6 Self Diagnostic Test

9. TROUBLESHOOTING
9.1 The Plotter is Turned On But Doesn’t Operate
9.2 Media Loading Operations
9.3 Cutting Operations
9.4 Error Messages in GP-GL Command Mode
9.5 Error Messages in HP-GL Command Mode
9.6 ARMS Error Messages
9.7 Other Error Messages
9.8 Caution Message
9.9 Troubleshooting of experience

10. PARTS LIST
10.1 Outer Casing CE6000-40/60/Plus
10.2 Outer Casing CE6000-120/120AMO/120Plus
10.3 Outer Casing CE6000-120AP
10.4 Outer Casing CE6000-120AP (New)
10.5 Main Frame CE6000-40/60/Plus
10.6 Main Frame CE6000-120/120AMO/120 Plus/120AP
10.7 Pen Block CE6000-40/60/120/120AMO/Plus
10.8 Pen Block CE6000-120AP
10.9 Control Panel
10.10 Wiring Harness
10.11 Stand CE6000-60/Plus, ST0100
10.12 Stand CE6000-120/120AMO/120Plus, ST0101
10.13 Option Basket CE6000-60/Plus, PG0100
10.14 Option Basket CE6000-120/120AMO/120Plus, PG0101
10.15 Stand CE6000-120AP, ST0102
10.16 Basket CE6000-120AP, PG0101
10.17 Other Parts

11. BLOCK DIAGRAMS AND CIRCUIT DIAGRAMS
11.1 Block Diagrams
11.2 Circuit Diagrams
12 Target electrical component for WEEE instruction