HP DesignJet 10000s Service Manual and Parts List Manual

Accurate, clear and concise text, combined with detailed illustrations, lists of error code, instruction and diagrams, guide you through procedure of repair, remediate, maintenance and adjustments your copier, printer or scanner.
Present service manual and parts list manual HP DesignJet 10000s contain clear instructions and procedures on how to fix the problems occurring in your equipment.
The information contained in this repair manual is necessary for the repair, but also prevention, resulting in a longer life of your equipment.
Format of the manual: PDF, makes it easy to navigate, instant download and print. English language.
To see what contain, please read table of contents:

Troubleshooting System Error Codes
Performing a Service Test on a Failed Assembly
Performing the Necessary Service Calibrations or Adjustments
Solving Print Quality Problems
The Printer does not Power ON
Cover Sensors are not Working
The File Sent is Not Processed Immediately
Troubleshooting Media Jam Messages
Media Jams Occur Frequently
Print Speed is Very Slow
No Ink Message when there is Enough Ink
Abnormal Sound Coming from the Printer
Front Panel is Not Working
Heater Panel is Not Working
Solving Heater Problems
Power ON Heater Power Switch appears on Heater Panel
Heater Does NOT become Hot
Abnormal Temperature is Displayed
The Heater Temperature Becomes Extremely High
Initializing Continuously Appears on the Heater Panel
Power Save Mode Continuously Appears on the Heater Panel
Special Power On Procedure
Both NVRAM and Main PCA are Replaced Together

Self-Diagnostic Errors at Power On
System Error Codes
Heater Error Codes
System Error Codes

Tools Required
Calibrate the Printhead Adjustment Jig
Install the Printhead Adjustment Jigs in the Carriage
Set Printhead Voltage
Print the Printhead Adjustment Pattern
Perform Printhead Position Correction
Print the Check Printhead Pattern
Adjust the Printhead
Tip to Speed-Up the Printhead Adjustment

Diagnostics Self Test
Phone Support
Maintenance Mode Menus
Entering the Maintenance Mode
Basic Menu Operation
P. ADJ. (Printer Adjustment)
PH. ADJ (Printhead Adjustment)
PH. MAIN (Printhead Maintenance)
MNFG-PRN (Manufacturing Patterns)
ELECT (Electronics)
VOLT (Voltage Check)
Heater Panel Maintenance Mode

Adjustments and Calibrations
Belt Tension Adjustment
Carriage Height Adjustment
Scan-Axis Belt Tension Adjustment
Paper-Axis Belt Tension Adjustment
Timing Belt (for Feed/TUR Unit) Tension Adjustment
Wiping Station Height Adjustment
Wiper Belt Tension Adjustment
Wiper Blade Height Adjustment
Capping Station Height Adjustment
Printhead Capping Limit Adjustment
Carriage Shield Height Adjustment
Media Feed and Take-Up-Reel Unit Adjustment
Media End Sensor Adjustment
Media Slack Sensor Adjustment
Take-Up-Reel Sensors Adjustment
Platen Flatness Measurement and Adjustment
Wiping Position Calibration
Capping Position Calibration
Line Sensor Calibration (Side Margin)
Line Sensor Calibration (Top Margin)

Print Quality
Print Quality Troubleshooting Actions
Print Quality General Advice
Troubleshooting Print Quality Problems
Horizontal Lines Across the Image (Banding)
Images are Blurred
Bleeding, Repelling or Mottling Problems
Image is Completely Blank or Faded
Output Only Contains a Partial Print
The Printer Area is Stained
Part of Image is Missing at the Start of the Print
Print Quality is not Improved After Printhead Recovery
Troubleshooting Printhead Problems

Right Hand Covers
Left Hand Covers
Center Covers
Electronics Module
Control Panels
Carriage Assembly
Scan-Axis Assemblies
Paper Path Assemblies
Media Entry Assemblies
Take-Up-Reel Assemblies
Capping Assemblies
Wiping Assemblies
Ink Supply and Subtank Assemblies
Printer Stand and Waste Bottle
Media Feed and TUR Sensors
Service Tools

Front Panel
Heater Panel
Front Heater
Rear Heater
Center Platen
Vacuum Fan
Main PCA
Head Relay Board
Add-On (HEB2) Control PCA
Switching Power Supply Unit
Power Supply Unit
Heater Relay Assembly
Waste Bottle Sensor
Front Media Sensor
Rear Media Sensor
Media Lever Sensor
Rear Cover Sensor
Home Position Sensor
Paper-Axis Motor and Belt
Scan-Axis Motor and Belt
Carriage Drive Assembly (Includes Carriage Belt)
Encoder Strip
Trailing Cable
Printhead Cooling Fans
Printhead Connector Assembly
Carriage PCA
Air Damper
Encoder Sensor
Line Sensor
Ink Pump Assembly
Ink Supply Station (Left or Right)
IC Door Sensor (Left or Right)
Subtank Sensors
Capping Station Assembly
Capping Unit
Prime Assembly
Solenoid Assembly
Waste Bottle Holder and Sensor Assembly
Wiping Station Assembly
Wiper Cleaning Assembly
Wiper Blade
Wiper Belts
Pinchwheel Assembly
Drive Roller
Media Feed Drive Unit Assembly
Take-Up-Reel Drive Unit Assembly
Drive Unit Rollers
Drive Unit Timing Belt
Media Sensors (Media End, Media Slack and Take-Up-Reel)
White Nets (For Front and Rear Heaters)
Sub-Scroller Flange

Printheads Maintenance
Daily Inspection and Maintenance
Wiper Blade Cleaning
Moistening the Wiper Sponge
Capping Unit Cleaning
Waste Ink Bottle Disposal
IQ Print
Normal Printhead Recovery
When Leaving the Printer Off for more than 2 weeks
When Returning to the Printer after more than 2 weeks
If the Printer is Switched Off for less than 2 weeks
If the Printer is Switched Off for more than one Month