Roland SolJet PROII V SC-545EX Service Manual and Parts List Manual


Accurate and concise text, combined with detailed illustrations, lists of error code, instruction and diagrams, guide you through procedure of repair, remediate, maintenance and adjustments your copier, printer or scanner.
Present service manual and parts list manual Roland SolJet PROII V SC-545EX contain clear instructions and procedures on how to fix the problems occurring in your equipment.
The information contained in this repair manual is necessary for the repair, but also prevention, resulting in a longer life of your equipment.
Format of the manual: PDF, makes it easy to navigate, instant download and print. English language.
To see what contain, please read table of contents:

1) Structure & Spare Parts
1-1 COVERS
1-2 FRAME
1-3 HEAD CARRIAGE
1-4 DRIVE UNIT
1-5 CHASSIS
1-6 PINCH ROLLER
1-7 STAY ROLL
1-8 TOOL CARRIAGE
1-9 WIPER SYATEM
1-10 PUMP SYSTEM
1-11 INK SYSTEM
1-12 BASE FRAME
1-13 ACCESSORIES & STAND
1-14 TUC-1 CONTROLLER
1-15 TUC-1 OTHERS
1-16 TUC-1 ACCESSORIES
1-17 TU-550

2) Electrical Section
2-1 WIRING MAP
2-2 MAIN BOARD
2-3 HEAD / SERVO BOARD
2-4 SUB BOARD
2-5 TUC-1
2-6 HEATER BOARD
2-7 MAINTENANCE PARTS LIST

3) Replacement of Main Parts
3-1 HEAD REPLACEMENT
3-2 WIPER REPLACEMENT
3-3 CAP TOP REPLACEMENT
3-4 TOOL CARRIAGE REPLACEMENT
3-5 CARRIAGE MOTOR REPLACEMENT
3-6 PUMP REPLACEMENT
3-7 INK TUBE REPLACEMENT
3-8 BOARDS REPLACEMENT
3-9 BATTERY REPLACEMENT
3-10 CARRIAGE WIRE REPLACEMENT
3-11 ENCODER SCALE REPLACEMENT
3-12 PINCH ROLLER REPLACEMENT
3-13 CUTTER PROTECTION REPLACEMENT

4) Adjustment
4-1 SPECIAL TOOLS
4-2 SERVICE MODE
4-3 HOW TO UPGRADE FIRMWARE
4-4 HEAD ALIGNMENT
4-5 LIMIT POSITION & CUT DOWN POSITION INITIALIZE
4-6 LINEAR ENCODER SETUP
4-7 CAP HEIGHT ADJUSTMENT
4-8 CROP MARK SENSOR ADJUSTMENT
4-9 TOOL/CROP MARK SENSOR POSITION ADJUSTMENT
4-10 PRINT/CUT POSITION ADJUSTMENT
4-11 CALIBRATION (FEEDING DIRECTION)
4-12 TOOL HEIGHT ADJUSTMENT
4-13 TOOL PRESSURE ADJUSTMENT
4-14 CARRIAGE WIRE TENSION ADJUSTMENT
4-15 NETWORK BOARD INITIALIZE
4-16 OPERATION OF THE HEATER CONTROLLER
4-17 SETTING THE PARAMETER OF THE HEATER CONTROLLER

5) Supplemental Information
5-1 SENSOR MAP

6) Troubleshooting
6-1 WHITE FINE LINES / BANDING / MISSING DOT / SCRATCHY PRINTING / BLURRED PRINTING
6-2 IT DOESN’T PRINT AT ALL
6-3 INK DROPS ON MEDIA
6-4 SHIFTING IN PRINTING
6-5 VERTICAL BANDING
6-6 PRINT DOES NOT MATCH WITH CUT
6-7 STITCH CUT
6-8 START AND END POINTS DO NOT MATCH
6-9 DISTORTED FIGURE
6-10 MEDIA SHIFTING
6-11 MOTOR ERROR
6-12 ERROR MESSAGE/SERVICE CALL
6-13 HEATER TEMPERATURE FAILS TO REACH THE PRESET VALUE
6-14 RESULTS OF PRINTING ARE COARSE
6-15 ERROR MESSAGE (HEATER CONTROLLER)

7) Service Activities
7-1 INSTALLATION CHECK LIST
7-2 MAINTENANCE CHECK LIST
7-3 SPECIFICATION

Roland SolJet PROII V SC-545EX SJPROIIV SC545EX SJ PROII V SC 545EX PROII V 545 EX